Heat Setting Machine Recovery - Zhangjiagang Youcheng Composites Material Factory

Heat-setting machines emit hot exhaust contains many of the fabric itself, falling down a short fiber, and fats, if mixed, could change oil viscosity, it is easy to form a grease stain, it is difficult to remove. Through the cycle filter device, can be cleared at a high temperature above the hot exhaust gases, such as short fiber dust, and roll through the brush bristles, extrusion screw dust, auto exhaust box.
Features: This device filters using high temperature resistant V-belt drive, run a smooth, easy deviation. Taking into account the brush roller may not be completely cleaned up the staple fiber web filter, so near the inner surface of filter network also has the steam nozzle is installed, you can from time to time to carry out thorough cleansing filters to make it from time to time to ensure a high efficiency filter. This device can automatically cycle of treatment, in improving efficiency while also reducing the workload of the maintenance workers.

After filtering the hot exhaust gas flows through the catheter endothermic super client, super-heating duct, at the same time ultra-catheter to rapidly absorb heat from the endothermic heat delivered to the client side. At this point from the adjustable air blower at room temperature into the clean air, by the super client after catheter exothermic heating, and then directly to the drying room setting machine into a cloth drying room 2 mouth, forming the wind screens. Setting Machine primer pump hot air exhaust fan will have a negative pressure inside the drying room, drying room and setting machine into a cloth mouth is not sealed, at room temperature under normal circumstances would be the rapid adoption of the air into the mouth of cloth into the drying room added because of smoke and hot exhaust air generated by deletion. And now we have the clean hot air (when setting machine at 200 ℃ when the temperature usually about 130 ℃) to the drying room setting machine into a cloth drying room I 2 after the formation of the wind screens. Characteristics: 1) the use of ultra-catheter delivery, improve the transmission speed and efficiency. 2) The clean hot air to the drying room setting machine into a cloth drying room I formed two wind帘后, cut off from the outside cold air to enter, by its own drying room with added exhaust air generated missing. Can improve before and after two drying room temperature, so that it can improve drying efficiency. Enable users to the original basis of improve speed and reduce the occurrence of the phenomenon of water vapor, reducing the chromatic aberration finished.

After hot air back to using paragraph after the hot exhaust gas temperature is still relatively high, for chemical fiber knitted type of fabrics, this time the hot exhaust contains pui as a result of high temperature drying of organic produce, dye auxiliaries (including wax, solvent, emulsifier, Polymer monomer) and other substances, to allow its flow through heat exchanger (gas - liquid exchange), its temperature dropped further, so that some fats and dyes began to liquefaction. Against the cotton material, with its own grease on the relatively small, so at this time can only return with hot water heat exchanger, rather than making static electricity removal device. Features: 1) water back and forth with energy, with a high rate of return. 2) reuse for different requirements, can be used for flexible adjustment. 3) for chemical fiber knitted type of fabrics can also play a role in recovery of some grease.

After the hot water and reuse the hot exhaust gas after paragraph also contains some low-dew-point fats and dyes, by atomizing humidification and change the exhaust than the resistance, and then flows through the electrostatic degreasing paragraph. High Voltage Electric Field in the role, the ionized gas fumes, oil mist particles are charged by the charge of the oil mist particles in the electric field force to collecting great movement, great build-up in the upper reaches of collecting tank to collect. Can be more thorough recovery of waste oil, reduce emissions of harmful substances. Features: 1) sub-type recovery of waste oil, so that the recovery efficiency. 2) the use of aerosol humidification device, simply dry up easily plug electrostatic equipment, equipment cleaning frequency of less than higher. 3) a variety of regular cleaning of equipment required are for the removable modular combinations, so that a convenient day-to-day cleaning of equipment maintenance, but also conducive to the maintenance of the replacement of these parts.

Finally, "treatment" had been achieved through the exhaust chimney directly emptying.